Passed TS1, DIAG H2+ and CFG H3

[biller]

Hello all,
I took the exam again and passed.
I got TS1/ H2+ / H3 config
*
Following will be my feedbacks for all of you. Mostly all questions from workbook was same in exam.
*
TS1
====
*
Incident 1
=======
*
SW2 ==> fix mac-add under e1/0 ( sh / no sh )
R101 ==> fix mac-add under e0/0 ( sh / no sh )
*
Incident 2
=======
*
R17 ==> Just add “ ppp ipcp route default “ under s4/0
*
Incident 3
=======
*
R22 ==> wrong subnets ( change /30 to /29 )
==> no passive-int e0/0
*
*
Incident 4
=======
*
R13 ==> no ip prefix filter seq 5 deny 145.14.14.14/32
*
Incident 5
=======
*
R21 ==> wrong prefix ( add “ ip prefix 194 seq 10 permit 194.1.0.0/16 le 32 )
==> add “network 134.21.21.21 mask 255.255.255.255”
R22 ==> add “neighbor IBGP next-hop-self “
*
Incident 6
=======
*
R25 ==> wrong subnets announcement for e0/0 ( change /128 to /64 )
*
Incident 7
=======
*
R15 ==> add “ ip nhrp redirect “ under tun 0
R18 ==> add “ ip nhrp shortcut “ under tun 0
R19 ==> copy tunnel parameters ( mtu, authentication, tunnel key , etc ) into tun 0
R20 ==> no passive-int e0/1
*
Incident 8
=======
*
R7 ==> no ip nat source list …. & add “ ip nat inside source list … “
R3 ==> route-target import ( same as workbook )
R4 ==> route-target import ( same as workbook )
*
Incident 9
=======
*
R24 ==> wrong crypto transform-set
==> secondary ip information set under e0/0
*
Incident 10
========
*
R23 ==> ip domain-lookup
NAS ==> ip domain-lookup
*
################################################## ##########################
*
DIAG ( TS2 plus )
===========
Two of the tickets were same as workbook
*
Ticket 1
=====
a. shutdown CE1 interface
b. Higher preference gateway information is sent out
c. Unknown Devices on LAN
d. Capture file open & filter “ icmpv6.type==134” , seq. 227
*
Ticket 2
=====
a. R2 has wrong RP configuration
b. Why 10.1.4.0/24 (RP) not in R2 RIB ?
c. ip mroute 10.1.4.1 0.0.0.0 10.0.0.14
*
################################################## #########################
*
CFG ( H3 )
=======
*
Section 1.1
========
*
All Questions were same as workbook
*
Except : There was already “ no spanning-tree mst simulation post global “ on SW300/301/310
*
Section 1.2
========
*
All Questions were same as workbook
*
Notes: Be careful about Portchannel interface assign on SW300/301 /400/401 /500/501
*
Section 1.3
========
*
All Questions were same as workbook
*
Section 1.4
========
*
All Questions were same as workbook
*
Section 2.1
========
*
All Questions were same as workbook
*
Section 2.2
========
*
All Questions were same as workbook
*
Section 2.3
========
*
All Questions were same as workbook
*
Notes ==> We cannot touch or telnet to R100, just configure on R42
==> On SW400/ SW401, enable ospf for “ vlan 2000, vlan 2001 “ . Preconfig don’t have this.
Verify ==> After all section finished, “tracert 100.100.100.100” from Server1 /Server2 /SW600 /SW500
*
Section 2.4
========
*
All Questions were same as workbook
*
Section 2.5
========
*
All Questions were same as workbook
*
Section 2.6
========
*
All Questions were same as workbook
*
Section 2.7
========
*
All Questions were same as workbook
*
Notes ==> I was use prefix-list and permit only 10.x.0.0/16 subnets over R14 for both ISP site and Remote-site (DMVPN)
*
Section 2.8
========
*
All Questions were same as workbook
*
Section 2.9
========
*
All Questions were same as workbook
*
Section 2.10
========
*
All Questions were same as workbook
*
Notes ==> RP announce & discovery is using Lo1. All pim interface configuration was already done in exam.
*
Section 2.11
========
*
All Questions were same as workbook
*
Notes ==> Firstly , i use same scope number for both announce and discovery commands on R30.
ip pim send-rp-announce lo 1 scope 2 group-list 1
ip pim send-rp-disc lo 1 scope 2
*
Reason is : SW300 cannot found rp-mapping for both multicast-group (239.130.1.1 / 239.250.1.1)
*
Section 3.1
========
*
All Questions were same as workbook
*
Notes ==> Lo0 interface will be 100.x.x.x.x ( 100.3.3.3, 100.4.4.4., 100.6.6.6, 100.5.5.5 )
*
Section 3.2
========
*
All Questions were same as workbook
*
Section 3.3
=========
*
All Questions were same as workbook
*
Section 3.4
========
*
All Questions were same as workbook
*
Notes ==> Announce Lo123 into BGP & static route 10.7.0.0 to 201.99.24.1
*
Section 4 & Section 5
=================
*
All Questions were same as workbook

[astauser]

Congratulation biller

can you please tell mi some non technical things as below

1:- i heard that there are 2 moniters in the exam,so what is displayed on 1st and 2nd moniter?
2:- The window in which topology is opened,can we make that window small(adjust)?
3:- The question set is open im new window?can we also adjust that window?
4:- Normally at home we open notepad using WIN+R and then search for notepad.So is that the same process in exam.In exam can we see the TASK BAR so it can be easy to open notepad
5:-how does it feels when we practise on our keyboard and in exam we face another keyboard,is it comfortable.


Thank u

[dund1212]

Thank bro :o kiss you :* , i hope many bro pass ccie share feedback ^^

[shikima]

Thank you!! :D and Gratz!!!

[shikima]

I have a question, do we need to put o remove this command?

All Questions were same as workbook
*
Except : There was already “ no spanning-tree mst simulation post global “ on SW300/301/310

[Nexus]

I have a question, do we need to put o remove this command?
All Questions were same as workbook
*
Except : There was already “ no spanning-tree mst simulation post global “ on SW300/301/310

Remove that command, you can test by yourself

[shikima]

Oh ok, thanks!

[JimmyLO89]

thanks for info

[irfanismail]

Congratulation biller

can you please tell mi some non technical things as below

1:- i heard that there are 2 moniters in the exam,so what is displayed on 1st and 2nd moniter?
2:- The window in which topology is opened,can we make that window small(adjust)?
3:- The question set is open im new window?can we also adjust that window?
4:- Normally at home we open notepad using WIN+R and then search for notepad.So is that the same process in exam.In exam can we see the TASK BAR so it can be easy to open notepad
5:-how does it feels when we practise on our keyboard and in exam we face another keyboard,is it comfortable.


Thank u

I have same questions too!

[ohnoaburd]

I have same questions too!

1. The lab is in a web browser. You can move that browser to either monitor. You can also open up individual questions in another browser window and move those windows to either monitor. Same w/ Putty, notepad, etc.
2. You can zoom in and out, but as I said, it's in a browser window.
3. Yes, like a browser window, you can min/maximize and drag to adjust.
4. No, you can't use Windows function keys. They have shortcuts on the desktop.
5. It's a standard (I think Dell) US keyboard