My friend Passed H3 yesterday

[nowever]

this is the feedback from my friend, He passed exam yesterday with CFG H3. I hope it help

**Hidden Content: Check the thread to see hidden data.**

[junitor]

Thank for sharing. can you please share the information about him, I want to contact him and ask him the information about Combat and CC Dreamer

[ccierscisco]

this is the feedback from my friend, He passed exam yesterday with CFG H3. I hope it help

***Hidden content cannot be quoted.***

thanks

[ccierscisco]

Section 2.7
Prefix filter requested on 14 and 15 as well, but at the end of the lab NAT’ing wouldn’t work.
I removed the prefix FILTER from 14 and 15 and all worked … I just took that loss instead of no pings to internet!!!
It means this section you failed and tunnel is not up if nat is not correct....Plz correct me ..I faced also this in my lab but failed in H3 config.

Section 3.4
Same as WB (LOGIC).
R24 was fully preconfigured, only thing I had to add was the static route (which is allowed) and also helps 10.7.0.0/16 go out (redistribute static preconfigured).
R71 had most of the ACL’s preconfigured and the NAT Pool, so used their templates.
However, all of them were missing/wrong ACL definitions.
I redid all the ACL/POOL, but used the name that they had pre-config.

This is also not clear from feedback what exactly you had done in R71 router

[Nexus]

Section 2.7
Prefix filter requested on 14 and 15 as well, but at the end of the lab NAT’ing wouldn’t work.
I removed the prefix FILTER from 14 and 15 and all worked … I just took that loss instead of no pings to internet!!!
It means this section you failed and tunnel is not up if nat is not correct....Plz correct me ..I faced also this in my lab but failed in H3 config.

Section 3.4
Same as WB (LOGIC).
R24 was fully preconfigured, only thing I had to add was the static route (which is allowed) and also helps 10.7.0.0/16 go out (redistribute static preconfigured).
R71 had most of the ACL’s preconfigured and the NAT Pool, so used their templates.
However, all of them were missing/wrong ACL definitions.
I redid all the ACL/POOL, but used the name that they had pre-config.

This is also not clear from feedback what exactly you had done in R71 router

Section 2.7: That is a big prolem, many guys reported he cannot handle this issue.
Section 2.8: I know two variation with this quetsion, depends on the the output you get, the ACL will be modified.

[ccierscisco]

Section 2.8: I know two variation with this quetsion, depends on the the output you get, the ACL will be modified.

Nexus:Can you elaborate the two variation of sec 2.8 ?

[Nexus]

Section 2.8: I know two variation with this quetsion, depends on the the output you get, the ACL will be modified.

Nexus:Can you elaborate the two variation of sec 2.8 ?

This the ouput Cisco will give you. Let me do the lab and share it with you.

[CiscoCCDE]

This the ouput Cisco will give you. Let me do the lab and share it with you.

Please do it and share with us

[abanalaccie]

Do you really think that is really mandatory to filter in R14/R15 if nat pool is configured ? i don't think so because there is no really solution for this. You can also change the nat pool to do by interface and do the filtering it should be work

[ccierscisco]

yes it is asking in exam

[hainhtet]

Please do it and share with us . congra!

[zr595576323]

yes it is asking in exam

[cciecandidate]

Thanks. Congratulations

[cciecandidate]

Congratulations. do you need to do IBGP in Medium Office ?

[Redes2019]

Thank friend

[jpfu02]

Hi guys,

May I know if there is a workbook from Combat or CC Dreamer? I am about to do my 4th attempt and I want to pass it this time.

Thanks.

[kaka]

Hi guys,

May I know if there is a workbook from Combat or CC Dreamer? I am about to do my 4th attempt and I want to pass it this time.

Thanks.

In our forum, there is many stuff from C4C and SPOTO.
that is the link you can donwload a workbook from C4C.

**Hidden Content: Check the thread to see hidden data.**

[jpfu02]

In our forum, there is many stuff from C4C and SPOTO.
that is the link you can donwload a workbook from C4C.

***Hidden content cannot be quoted.***

Thank you Kaka!

I have done both versions H2 and H2+, the first one, I hit a bug and never got IP addresses for the remote offices (PPPoE) due to an issue on the server, a reload fix the problem but I didn't know that you can do such thing back then, and freak out and lost tone of precious time.

Second time was H3, didn't have much information about this version, but now I am using 1.7 hopefully is good enough, and for the last one, I got H2+, where I have issues with the control plane policing where you cannot use the DENY statement in the ACL. I got 0 for that part, and L3 was not good either.

Not sure how to acomplish the dual redistribution on R9 and R10, any information will be highly appreciated.

Regards

[ccierscisco]

In our forum, there is many stuff from C4C and SPOTO.
that is the link you can donwload a workbook from C4C.

***Hidden content cannot be quoted.***

[gridenco]

thanks thanks thanks

[cciers3rd]

That's great