Passed TS1, DIAG H3+ and CFG H2+
This is my feedback. One Good turn they say deserves another and I think, it behoves on me to do just that, got TS1/H3+/H2+.
Diag
Got H3+
1. used bootp and my sequence number was 114. the rest were same as WB
2. TCL was where Cisco went bananas. in my case, the tcp flow did not show anywhere "sudo poweroff" or any of the commands that we are familiar with. In my case, it was "r"
TS1
Pretty easy and finished that within an hour but had to go over it three times just to be sure I was on the right path because in some tickets, the number of faults I resolved to get the tickets working were less than what Cisco said there were. for example, Cisco said "This ticket involves two (2) separate faults" and yet, I got it resolved with just one fault. In some cases, the resolution of one ticket lead me into automatically getting the other done if you know what I mean.
For example, when I finished with ticket 9, ticket 10 worked "automagically" for me and I didn't have to do anything there. I guess the solution Cisco envisaged was just to remove the secondary IP address on R24.
Other few nuances were also where the testing of the solution was required. For example, Cisco Required ping to internet from R105 instead of R106.
CFG
1. in my case, I got H2+ CFG and section 1.1 for example did not require "snmp-server enable traps syslog"
2.There was no ospf preconfiguration on DC (AS 65002) devices and Cisco requested not to use the "network" command anywhere in the ospf configuration in the DC.
3. Watch the vrf name: it was Corp instead of CORP in the Branch Network.
4. vrfs did not have RD preconfigured.
5. Headquarters and Main office had ospf and bgp pre-configured but needed to be tweaked to get the desired output requested by Cisco. Same with Jacobs Office network
6. Jacobs Core Network PE routers didn't have vrf configured at all.
7. Jacob CE routers (R55/56) had a bare BGP configuration. no prefix-list , no route-map for redistribution and redistribution between the EIGRP and BGP completely not pre-configured. had to configure all of that.
8. Jamesons CE routers needed to allow AS in and not PE routers overriding the AS.
9. section 4.1 actually required the use of only "permit" in solution
All in all,Combat and CC Dreamer deserve commendations and I dedicate my number to them. If you understand the topologies and the traffic flow coupled with the WBs,you are good to go.
Thanks everyone.
Re: Passed TS1, DIAG H3+ and CFG H2+
Thanks man, it was ur first attemp?
Congratulations!!
Re: Passed TS1, DIAG H3+ and CFG H2+
congratulation
5. Headquarters and Main office had ospf and bgp pre-configured but needed to be tweaked to get the desired output requested by Cisco. Same with Jacobs Office network
Can you tell us what tweaked you had done to match the output
Re: Passed TS1, DIAG H3+ and CFG H2+
Quote:
Originally Posted by
ccierscisco
congratulation
5. Headquarters and Main office had ospf and bgp pre-configured but needed to be tweaked to get the desired output requested by Cisco. Same with Jacobs Office network
Can you tell us what tweaked you had done to match the output
I think, he modified router-id in BGP, OSPF, add some interfaces into ospf. As I know some guys reported: Cisco gave him the pre-configured but it is not right and lack some information and your task must correct.
Re: Passed TS1, DIAG H3+ and CFG H2+
Quote:
Originally Posted by
Nexus
I think, he modified router-id in BGP, OSPF, add some interfaces into ospf. As I know some guys reported: Cisco gave him the pre-configured but it is not right and lack some information and your task must correct.
That is right mate. in the real exam you will see many pre-conigured but we need to add some missing interface into OSPF and BGP router-id.
Re: Passed TS1, DIAG H3+ and CFG H2+
Hey buddy, can you be a little bit more specific?
I'm asking just because many of posts that i see lately from guys that passed - they end up banned on the forum... Meaning - glorifying vendors, but giving the hints to something that is already very known (bgp rid etc..)
Cheers and good luck to you
Re: Passed TS1, DIAG H3+ and CFG H2+
Re: Passed TS1, DIAG H3+ and CFG H2+
thanks for your feedback! is the next-hop-self was configured between R11/R12 ?
How did you configure the ttl security part and what was the restrictions ? i heard a variation on this to not use a deny statement on the acl...
Re: Passed TS1, DIAG H3+ and CFG H2+
Quote:
Originally Posted by
abanalaccie
thanks for your feedback! is the next-hop-self was configured between R11/R12 ?
How did you configure the ttl security part and what was the restrictions ? i heard a variation on this to not use a deny statement on the acl...
check in this post
**Hidden Content: Thanks to see the content**
