Results 1 to 10 of 10

Thread: Passed TS1, DIAG H2+ and CFG H3

  1. #1

    Passed TS1, DIAG H2+ and CFG H3

    Hello all,
    I took the exam again and passed.
    I got TS1/ H2+ / H3 config
    *
    Following will be my feedbacks for all of you. Mostly all questions from workbook was same in exam.
    *
    TS1
    ====
    *
    Incident 1
    =======
    *
    SW2 ==> fix mac-add under e1/0 ( sh / no sh )
    R101 ==> fix mac-add under e0/0 ( sh / no sh )
    *
    Incident 2
    =======
    *
    R17 ==> Just add “ ppp ipcp route default “ under s4/0
    *
    Incident 3
    =======
    *
    R22 ==> wrong subnets ( change /30 to /29 )
    ==> no passive-int e0/0
    *
    *
    Incident 4
    =======
    *
    R13 ==> no ip prefix filter seq 5 deny 145.14.14.14/32
    *
    Incident 5
    =======
    *
    R21 ==> wrong prefix ( add “ ip prefix 194 seq 10 permit 194.1.0.0/16 le 32 )
    ==> add “network 134.21.21.21 mask 255.255.255.255”
    R22 ==> add “neighbor IBGP next-hop-self “
    *
    Incident 6
    =======
    *
    R25 ==> wrong subnets announcement for e0/0 ( change /128 to /64 )
    *
    Incident 7
    =======
    *
    R15 ==> add “ ip nhrp redirect “ under tun 0
    R18 ==> add “ ip nhrp shortcut “ under tun 0
    R19 ==> copy tunnel parameters ( mtu, authentication, tunnel key , etc ) into tun 0
    R20 ==> no passive-int e0/1
    *
    Incident 8
    =======
    *
    R7 ==> no ip nat source list …. & add “ ip nat inside source list … “
    R3 ==> route-target import ( same as workbook )
    R4 ==> route-target import ( same as workbook )
    *
    Incident 9
    =======
    *
    R24 ==> wrong crypto transform-set
    ==> secondary ip information set under e0/0
    *
    Incident 10
    ========
    *
    R23 ==> ip domain-lookup
    NAS ==> ip domain-lookup
    *
    ################################################## ##########################
    *
    DIAG ( TS2 plus )
    ===========
    Two of the tickets were same as workbook
    *
    Ticket 1
    =====
    a. shutdown CE1 interface
    b. Higher preference gateway information is sent out
    c. Unknown Devices on LAN
    d. Capture file open & filter “ icmpv6.type==134” , seq. 227
    *
    Ticket 2
    =====
    a. R2 has wrong RP configuration
    b. Why 10.1.4.0/24 (RP) not in R2 RIB ?
    c. ip mroute 10.1.4.1 0.0.0.0 10.0.0.14
    *
    ################################################## #########################
    *
    CFG ( H3 )
    =======
    *
    Section 1.1
    ========
    *
    All Questions were same as workbook
    *
    Except : There was already “ no spanning-tree mst simulation post global “ on SW300/301/310
    *
    Section 1.2
    ========
    *
    All Questions were same as workbook
    *
    Notes: Be careful about Portchannel interface assign on SW300/301 /400/401 /500/501
    *
    Section 1.3
    ========
    *
    All Questions were same as workbook
    *
    Section 1.4
    ========
    *
    All Questions were same as workbook
    *
    Section 2.1
    ========
    *
    All Questions were same as workbook
    *
    Section 2.2
    ========
    *
    All Questions were same as workbook
    *
    Section 2.3
    ========
    *
    All Questions were same as workbook
    *
    Notes ==> We cannot touch or telnet to R100, just configure on R42
    ==> On SW400/ SW401, enable ospf for “ vlan 2000, vlan 2001 “ . Preconfig don’t have this.
    Verify ==> After all section finished, “tracert 100.100.100.100” from Server1 /Server2 /SW600 /SW500
    *
    Section 2.4
    ========
    *
    All Questions were same as workbook
    *
    Section 2.5
    ========
    *
    All Questions were same as workbook
    *
    Section 2.6
    ========
    *
    All Questions were same as workbook
    *
    Section 2.7
    ========
    *
    All Questions were same as workbook
    *
    Notes ==> I was use prefix-list and permit only 10.x.0.0/16 subnets over R14 for both ISP site and Remote-site (DMVPN)
    *
    Section 2.8
    ========
    *
    All Questions were same as workbook
    *
    Section 2.9
    ========
    *
    All Questions were same as workbook
    *
    Section 2.10
    ========
    *
    All Questions were same as workbook
    *
    Notes ==> RP announce & discovery is using Lo1. All pim interface configuration was already done in exam.
    *
    Section 2.11
    ========
    *
    All Questions were same as workbook
    *
    Notes ==> Firstly , i use same scope number for both announce and discovery commands on R30.
    ip pim send-rp-announce lo 1 scope 2 group-list 1
    ip pim send-rp-disc lo 1 scope 2
    *
    Reason is : SW300 cannot found rp-mapping for both multicast-group (239.130.1.1 / 239.250.1.1)
    *
    Section 3.1
    ========
    *
    All Questions were same as workbook
    *
    Notes ==> Lo0 interface will be 100.x.x.x.x ( 100.3.3.3, 100.4.4.4., 100.6.6.6, 100.5.5.5 )
    *
    Section 3.2
    ========
    *
    All Questions were same as workbook
    *
    Section 3.3
    =========
    *
    All Questions were same as workbook
    *
    Section 3.4
    ========
    *
    All Questions were same as workbook
    *
    Notes ==> Announce Lo123 into BGP & static route 10.7.0.0 to 201.99.24.1
    *
    Section 4 & Section 5
    =================
    *
    All Questions were same as workbook

  2. The Following User Says Thank You to biller For This Useful Post:

    jaruphat (10-06-2018)

  3. #2

    Re: Passed TS1, DIAG H2+ and CFG H3

    Congratulation biller

    can you please tell mi some non technical things as below

    1:- i heard that there are 2 moniters in the exam,so what is displayed on 1st and 2nd moniter?
    2:- The window in which topology is opened,can we make that window small(adjust)?
    3:- The question set is open im new window?can we also adjust that window?
    4:- Normally at home we open notepad using WIN+R and then search for notepad.So is that the same process in exam.In exam can we see the TASK BAR so it can be easy to open notepad
    5:-how does it feels when we practise on our keyboard and in exam we face another keyboard,is it comfortable.


    Thank u

  4. #3

    Re: Passed TS1, DIAG H2+ and CFG H3

    Thank bro kiss you :* , i hope many bro pass ccie share feedback ^^

  5. #4

    Re: Passed TS1, DIAG H2+ and CFG H3

    Thank you!! and Gratz!!!

  6. #5

    Re: Passed TS1, DIAG H2+ and CFG H3

    I have a question, do we need to put o remove this command?

    All Questions were same as workbook
    *
    Except : There was already “ no spanning-tree mst simulation post global “ on SW300/301/310

  7. #6

    Re: Passed TS1, DIAG H2+ and CFG H3

    Quote Originally Posted by shikima View Post
    I have a question, do we need to put o remove this command?
    All Questions were same as workbook
    *
    Except : There was already “ no spanning-tree mst simulation post global “ on SW300/301/310
    Remove that command, you can test by yourself

  8. #7

    Re: Passed TS1, DIAG H2+ and CFG H3

    Oh ok, thanks!

  9. #8

    Re: Passed TS1, DIAG H2+ and CFG H3

    thanks for info

  10. #9

    Re: Passed TS1, DIAG H2+ and CFG H3

    Quote Originally Posted by astauser View Post
    Congratulation biller

    can you please tell mi some non technical things as below

    1:- i heard that there are 2 moniters in the exam,so what is displayed on 1st and 2nd moniter?
    2:- The window in which topology is opened,can we make that window small(adjust)?
    3:- The question set is open im new window?can we also adjust that window?
    4:- Normally at home we open notepad using WIN+R and then search for notepad.So is that the same process in exam.In exam can we see the TASK BAR so it can be easy to open notepad
    5:-how does it feels when we practise on our keyboard and in exam we face another keyboard,is it comfortable.


    Thank u
    I have same questions too!

  11. #10

    Re: Passed TS1, DIAG H2+ and CFG H3

    Quote Originally Posted by irfanismail View Post
    I have same questions too!
    1. The lab is in a web browser. You can move that browser to either monitor. You can also open up individual questions in another browser window and move those windows to either monitor. Same w/ Putty, notepad, etc.
    2. You can zoom in and out, but as I said, it's in a browser window.
    3. Yes, like a browser window, you can min/maximize and drag to adjust.
    4. No, you can't use Windows function keys. They have shortcuts on the desktop.
    5. It's a standard (I think Dell) US keyboard

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •